Top 10 Appliance Connector

Easyflex gas connectors are CSA certified to ANSI Z21.24 CSA/CGA 6.10 Standard connectors for gas appliance and ANSI Z21.75 CSA/CGA 6.27 Standard Connectors for outdoor gas appliance and manufactured homes. The corrosion resistant yellow coating protects the product from exposure from harsh weather and certain chemicals. See BTU chart for rating.

CAMBRIDGE Performance driven and high quality products are preferred by industry leaders in the Electrical, HVAC, Automotive Aftermarket, Plumbing and Home Improvement Markets. Be sure to view all of our Amazon ASINs for a product solution that works best for you.

Product Description

Protect your home with a Fluidmaster Braided Stainless Steel Water Heater Connector. This 3/4-Inch female iron pipe by 3/4-Inch female iron pipe connector connects your water heater to the water supply. Made from high quality PVC and braided in stainless steel, this connector won’t burst or leak in even the highest pressure conditions.

From the Manufacturer

Protect your home with a Fluidmaster Braided Stainless Steel Water Heater Connector. This 3/4-Inch female iron pipe by 3/4-Inch female iron pipe connector connects your water heater to the water supply. Made from high quality PVC and braided in stainless steel, this connector won’t burst or leak in even the highest pressure conditions.

Stainless Steel Steam Dryer Installation Kit Includes Everything You Need To Install Your Steam Dryer-
6′ Hose (3/4″ FHT x 3/4″ FHT) with 90 Degree Elbow,
Inlet Adapter, “Y” Connector
1 Foot Feed Hose

The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.

Product Description

Are you replacing a 5+ year-old ice maker connector hose or hooking up a new ice maker? This 15 ft. Braided Stainless Steel Ice Maker Connector from Certified Appliance Accessories is just what you need. It is corrosion-resistant inside and out plus bends freely for easier installation in cramped spaces.

From the Manufacturer

Ice Maker Connectors (15-Foot)

BrassCraft’s 3/8 In. Female Flare (1/2 In. MIP) EFV x 1/2 In. MIP x 72 In. Safety+PLUS Gas Appliance Connector is 1/2 In. OD (3/8 In. ID) with a maximum operating capacity of 49,100 BTU’s. This Safety+PLUS gas connector combines excess flow technology with the advanced corrosion resistance of ProCoat, to provide a safer gas connector for home and family. In the event of a gas line rupture or disconnect, the Safety+PLUS valve restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. BrassCraft’s stainless steel gas connector is protected with a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products. ProCoat coating is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

Perfect for gas logs, garage heaters, gas stoves and wall mounted heaters. Size: 3/8 inch, Compatible With: Heaters, logs, ranges, dryers, etc., Product Type: Connection kits, Fuel Type: Propane/natural gas

Product Description

For years, licensed plumbers, electricians and appliance installers have relied on Certified Appliance Accessories for their power cords, hoses and connectors. Now you can too. Enjoy the convenience offered by this dryer cord from Certified Appliance Accessories. Its flexibility and durability ensure a reliable connection for your next home installation project. This high-quality dryer cord has been thoroughly tested and is backed by a 5-year limited warranty. Follow our illustrated, step-by-step directions included in the packaging. Always consult your appliance’s installation instructions. Check your appliance’s manual for the correct specifications to ensure this is the right cord for you. Thank you for choosing Certified Appliance Accessories—Your Appliance Connection Solution.

From the Manufacturer

5 foot 4-wire dryer cords are 250V closed eyelet and are UL Listed.